|
cam?
Aug 11, 2010 14:39:43 GMT -5
Post by Jon Hart 77 on Aug 11, 2010 14:39:43 GMT -5
ok well workin on getting a sbc350 its goin to be perdy much stock...it has an after market cam in it but the owner does not know the specs of it....yea i know not really that important but it is due to the fact that i am plannin on getting a carb and dist combo from gard for it.....now i am wanting to know what kind of cam i should get i was told i should get an eldebrock 2102 for it any input would be good
|
|
|
cam?
Aug 11, 2010 22:38:17 GMT -5
Post by helm024j on Aug 11, 2010 22:38:17 GMT -5
it realy depends on your wants,low or high optimum rpm.if you dont want to turn more than 6000 then the 2102 will work.also depends on what intake setup ur runing. i have a 350 w/a lopey cam had a 4bl aluminum street/strip w/a holly dbl pumper then a 650 edelbrock.i tried an ol 2bl and rochester set up and found it was a beautiful match..good luck hope it turns out the way you want
|
|
|
cam?
Aug 12, 2010 18:55:15 GMT -5
Post by 307ci on Aug 12, 2010 18:55:15 GMT -5
i wouldnt get one with a cam,,, cams create heat,,, heat is not good
|
|
|
cam?
Aug 12, 2010 22:24:24 GMT -5
Post by Jon Hart 77 on Aug 12, 2010 22:24:24 GMT -5
engines dont run without cams
|
|
|
cam?
Aug 12, 2010 22:30:10 GMT -5
Post by helm024j on Aug 12, 2010 22:30:10 GMT -5
|
|
|
cam?
Aug 13, 2010 16:12:54 GMT -5
Post by Jon Hart 77 on Aug 13, 2010 16:12:54 GMT -5
o and for the record engines require heat to run:P
|
|
|
cam?
Aug 29, 2010 21:19:03 GMT -5
Post by helm024j on Aug 29, 2010 21:19:03 GMT -5
well what did u decide to put in ?
|
|
|
cam?
Sept 3, 2010 12:21:37 GMT -5
Post by Jon Hart 77 on Sept 3, 2010 12:21:37 GMT -5
i got the edelbrock 2102 im goin to work on putting the moter together this winter takeing it down to the block perdy much to make sure its all good to go and get a carb and dist from gard
|
|
|
cam?
Jan 3, 2011 17:48:57 GMT -5
Post by coltabbott42 on Jan 3, 2011 17:48:57 GMT -5
my motor is at the shop right now. gettin it hottanked and unfortunately they have to bore it over after gettin everything hot tanked, bored, crank ground down, and the rebuild kit, its gonna cost me 640. Im gonna use an RV cam ;D
|
|
|
cam?
Jan 3, 2011 18:17:45 GMT -5
Post by 307ci on Jan 3, 2011 18:17:45 GMT -5
i got an RV cam in my driver 68 chevy pickup and love it in there, creates alot of horse for the little sbc 307
|
|
|
cam?
Jun 24, 2011 17:18:52 GMT -5
Post by derbyxxx on Jun 24, 2011 17:18:52 GMT -5
i got 350.2 bolt block power pack heads comp in the ball park of 11 to 1 11.5 to 1 with a 501 lift cam 2 barrel holley
|
|